Glow
Amazing glow, every day
MOLDERM® GLOW is part of Molderm Aesthetics’ pioneering anti-aging program which also includes MOLDERM® GLOW+.
MOLDERM® GLOW is a non-crosslinked gel designed to restore and repair the skin’s lost elasticity and firmness. MOLDERM® GLOW recreates the skin’s original glow and vitality.
Its moisturizing properties make it exemplary for the treatment of dry skin and existing fine lines. It also reduces the incidence of nye fine lines.
Obtained by bio-fermentation.
Thanks to our patented Fine-Tuning Technology™, we achieve almost the entire human molecular spectrum, which provides a hundred percent integration into the skin’s tissue with maximum effect, without immediate fluid accumulation and inflammatory processes in the skin.
The total active process in the skin to restore a good balance in the tissues is clinically proven to be higher and longer than competing products on the market.
The next generation bio-stabilizer
Unlike other products on the market where they tried to reach a wider molecular spectrum via so-called ”hybrid products” and used two different molecular chains (low molecular weight and high molecular weight), MOLDERM® GLOW stretches, thanks to Fine-Tuning Technology™, across an unbroken spectrum through low, high and ultra-high molecular weight. This means that the anti-aging process begins immediately in all layers of the skin and is not divided into different stimulation phases with varying results.
MOLDERM® GLOW is intended for hydration of the skin on the face, neck, décolletage, lips, and hands.
MOLDERM® GLOW should be injected into the middle layer of the dermis.
MOLDERM® GLOW should be used in combination with MOLDERM® GLOW+ as a course of treatment, for optimal results. About three treatments 1-2 weeks apart. After each treatment, a light massage is advantageously carried out to facilitate the spread of the product in the tissue.
A syringe with MOLDERM® GLOW contains 40 mg of hyaluronic acid.
See the treatment plan below for optimal results.
Treatment plan for GLOW & GLOW+
A complete treatment plan to stabilize and stimulate the skin.
The processing period begins according to the table below with MOLDERM® GLOW, and then closes with MOLDERM® GLOW+.
The treatments take place with 1-2 week intervals.
MOLDERM® GLOW+ should only be used on healthy and balanced skin. To achieve this, the performed treatments with MOLDERM® GLOW first with 1-2 week intervals according to the table below. When healthy and balanced skin are achieved, continue treatment with MOLDERM® GLOW+ in according to the table below. After each treatment carried out with advantage a light massage to ease the spread of the product in the tissue.
Behandling 1
GLOW +
To maintain a healthy balance in the skin and the production of collagen and elastin, the recommended treatment plan above two times a year.
Please note that the above should be seen as general recommendations
Consideration must always be given to the individual’s skin status during consultation.
Injection techniques for GLOW & GLOW+
MOLDERM® GLOW & GLOW+ must always be injected into the middle layer of the dermis.
After treatment should be a light massage to be performed on the treated areas to help the product to spread in the tissue.
Molderm® Picotage technique
Picotage technique should be performed with small bob on 0,05 – 0,1 ml of the product as a checkerboard pattern by placing the dots between them,
approx. 1,5-2 cm from each other. You can use the supplied 30G, 13mm needles or any 30G, 4mm mesoterapinåler.
Molderm® linear technology
Using the supplied needles it is possible to use Molderm® retrograde linear technique.
Fanning technique
When treating larger areas, it is recommended to use the retrograde fanning technique.
Molderm® 3-point cannula technique
With MOLDERM® GLOW & GLOW+ it is possible to use 27Gx40mm or 30Gx25mm blunt cannula and distribute the product with retrograde fanning technique or retrograde linear technique.
English 
Norwegian 
